TECHNICS SU 8200 Stereo Amplifier WORK 65 + 65 Watts RMS Vintage 1975 GOOD LOOK

TECHNICS SU 8200 Stereo Amplifier WORK 65 + 65 Watts RMS Vintage 1975 GOOD LOOK

Original from the Japanese market, it works on 100 volts, is completely restored and works perfectly at 100% - For shipments to Europeus countries it is supplied with a transformer to work on 220/240 volts

Technics SU-8200

¥ 62,800 (released in 1975)

A pre-main amplifier developed following the concept of the SU-8600.

The main amplifier circuit has an orthodox configuration of first stage differential amplification, voltage amplification and output stage.

In addition, the operating point of each stage transistor was examined to determine the best point to achieve low noise and low distortion.

The power supply unit uses a ± 4 power supply system with separate power supplies for the pre-unit and main unit.

In addition, the pre-section equalizer circuit and tone control circuit are all driven by a constant voltage power supply. This reduces transient crosstalk distortion and self-transient distortion, which tend to occur due to instantaneous large input, and reduces distortion during operation.

The equalizer circuit has a circuit configuration in which the differential amplifier stage of the current mirror load is the first stage first stage and the emitter follower of the low current load is used as the output stage. The differential amplifier stage of the current mirror load least noise can be selected.

The tone control circuit uses a circuit with a first stage differential current mirror load similar to the equalizer circuit, so that the tone quality is maintained and only the tone quality is adjusted.

The turnover frequencies can be switched to two levels for both low and high frequencies.

The newly developed 26-step attenuator is used for the volume, and the level setting between -30dB and -40dB, which is most frequently used, can be done in 2 dB steps.

It also comes with a Detent + Loudness terminal so that when the volume is low, the loudness functions to compensate for the lack of bass.

Equipped with low / high filter.

There was a wood case sold separately.

Type Stereo pre-main amplifier

Power Amplifier Unit

Effective output (both channels) 1 kHz : 65W + 65W (8 Ω)

20 Hz to 20 kHz : 60W + 60W (8 Ω)

Total harmonic distortion factor 0.08%

Output Bandwidth (both channels, 8 Ω) 5 hz to 70 khz -3dB

Frequency characteristic 5 hz ~ 100 khz + 0 -3dB

Signal-to-noise ratio (IHF-A) 115dB

Residual noise 0.3mV

Damping factor 50 (8 Ω)

Input Sensitivity / Impedance 1V/47k Ω

Load impedance Main, Remote : 4 Ω ~ 16 Ω

Main + Remote : 8 Ω ~ 16 Ω

Preamplifier Section

Input Sensitivity / Impedance Phono1, 2 : 2mV/47k Ω

Tuner, AUX, Tape Deck1, 2, Playback : 150mV/47k Ω

Phono Maximum Input (1 kHz, RMS) 150mV

Total harmonic distortion factor 0.08%

Signal-to-noise ratio (IHF-A) Phono:73dB

Tuner, AUX : 92 dB

Frequency characteristic Phono1 and 2 : RIAA standard curve ± 0.4 dB

Tuner, AUX : 5 hz to 75 khz + 0 to 3 db

Tone control Bass : 50 Hz, ± 12 dB

Treble : 20 kHz, ± 12 dB

Turnover frequencies Bass : 250 Hz, 500 Hz

Treble : 2.5 kHz, 5 kHz

Filter Low : 30 Hz, -6dB/oct.

High : 8 kHz, -6dB/oct.

Loudness control 100 Hz, + 8 dB (Volume -30dB)

Output voltage Pre Out : 1 v (rated), 8 v (maximum)

Tape Deck1, 2, Rec Out : 150 mv

<General>

Power supply voltage 100 VAC, 50/60Hz

Power consumption 150W

External dimensions Width 450x Height 173x Depth 345 mm

Weight 11.5kg

Attachment 1 x circuit protection fuse (5A)

Sold Separately Wood Case SH-780 (¥ 4,000)